Submission Details
SF3D`s MaxxMem score - Elite League
2617.3 marks with DDR3 SDRAM at 1130.8MHz
Ranking position
n/a
Global rank:
n/a
DDR3 SDRAM rank:
Points earned for overclocker league
-
Global Points
Not SF3D's best submission
-
Hardware Points
Not SF3D's best DDR3 SDRAM submission
Points earned for team league
-
Global Team Power Points (GTPP) Not Team Finland's best submission
0.0 Points
-
Hardware Team Power Points (HTPP) Not Team Finland's best DDR3 SDRAM submission
0.0 Points
Hardware details
CPU details
- Model: Intel Core i7 2600K 'Sandy Bridge'
- Cooling: Water (Custom)
- Cores: 5,512MHz(+62.12%)
-
Memory details
- Product: HyperX (classic)
- Cooling: Air (Stock)
- Type: 4096MB DDR3 SDRAM
- Speed: @ 1,131MHz
VGA details
- Model: ASUS GeForce GTX 580 (GF110) NVIDIA
- Cooling: Air (Stock)
- Speed: 772MHz (-.64%) / 1,000MHz (-.20%)
-
Mainboard details
- Manufacturer: ASUS
- Model: Maximus IV Extreme
- Cooling: Air (Stock)
- Chipset: P67
-
Recent Comments
SF3D commented on his own score:
Kingston KHX2133C8D3T 1K2/4GX Aircooled Scythe Kaze 3000rpm 1.9V still BCLK + divider limited. ASUS did great job with this board!
Asmola says:
Insane result! Good work Petri.
What would intel's engineers say about that voltage?
Turrican says:
congrats petri, that's a sick result.
TaPaKaH says:
Are you sure it's not mem limited? (with 7-7-6 most hypers stop scaling around 1080-1100 and at 1120 they're already barely benchable, no matter the volts)
zoro says:
great job! what about the other voltages pll,vccio,vccsa etc...thanks
zoro says:
great job! what about the other voltages pll,vccio,vccsa etc...thanks
SF3D says:
Sam- It is the cpu clocks which is limiting. I was already doing some higher freq runs, but with lower CPU speed. The score was worse + other issues. So I think with some new CPU I will try to show 1140Mhz+ runs for you
Zoro- 1.9 VDDR, 1.25 VCCSA, 1.1 VCCIO, 1.8VCPUPLL, Skew + driving voltage changes. Subtimings tweaked a tiny bit.
zoro says:
It could be bios limited! are you sure about vccsa and vccio? i would expect them to be reverced! is the cpu alive?
SF3D says:
Zoro- Yes, I am pretty sure that my eyes does not lie and my fingers set the correct values CPU is still in perfectly good condition.
_mat_ says:
Very nice result ... again! 30 GB/s finally done!
That is already a good cpu, I can tell you. Tested 5 until now and only one chip could do 108 BClock, but only with low cpu frequency. Higher frequencies on cpu and ram should need more VCCIO ... as much as the chip can take. Same as it was with Lynnfield.
Your voltages are really strange. Couldn't touch VCCSA on the UD7, because the whole system got unstable. VCCIO is very low for your memory frequency and timings.
SF3D says:
Thanks _mat_!
I think MIVE is very good board and very easy to use. I don't know why UD7 behaves that way
Gautam says:
1.9v vddr 2250+ 7-7-6 is awesome!
SF3D says:
You must mean "only" 1.9V
Dinos22 says:
wow i missed this one
well done dude this is a crazy OC. love it
where's ya superpi 32M mate
Please log in or register to comment.