Legend
This profile uses the same processor, at the same or lower speed, but has a higher XTU score. You might want to check out these profiles and try to apply it to your system.
The profile you have currently selected. Details are shown below the chart.
The profile you are analyzing. Settings of this profile are compared to the one you have selected.
leeghoofd`s Core i7 4770K at 5655.6MHz with an ASRock Z87 OC Formula motherboard
Recent Comments
leeghoofd commented on his own score:
Retesting 5ghz 1.385 Vcore CPU, no go over 6ghz 1core, 4/8 seems acceptable, CB at -115°C Not tweaked for performance (as usual)
Farjam says:
it was a 5ghz 4c8t 1.385v?
leeghoofd says:
yep, boots at 1.385 into win7 4/8 and runs 1M, AIDA CPU Queen, PhotoworXX on air.
Same CPU runs 4600 1.23Vcore AIDA stress test stable.
Re-testing the other one tonite... wished it could do 6100 1 core and 5800 all cores, but nope...
None optimised runs with the Corsair 2800C11 CFR kit... +1400 should be doable at them CPU speeds...
der8auer says:
Which batch is this one?
Farjam says:
so voltage on air is not always an important sign , my 6280mhz 01 chip was 4c8t 1.385 only for xp... but not bad with ln2... and i had an 6200 chip for 3Ds and 6050 for 06 that could not boot even 4.8 below 1.4v on air. and some 5ghz 1.41v that can not pass 06 @ 5700
der8auer says:
I think you still need low voltage on air but it has to scale on cold and high voltage.
My first 4670K did 1,15V 4500 MHz primestable which was a very good one. 6,3 GHz max valid and 6,1 for 32m.
I had a 4770K which did 4500 MHz at 1,175 Volt which is just a little bit worse but it did not scale on cold at all. 5,9 GHz max on LN2...
But the L313B996 ones which only did 4300 MHz at 1,275 V primestable were 5,5 to 5,6 max valid on LN2.
leeghoofd says:
Batch is L316B432 sr nr: 35310047A1952
This chip needs high uncore/NB, eg setting it at 50X would shutdown the setup at +5800Mhz, with 52X it was far more stable...
looking for better
Farjam says:
you looking for some chips like this? ...
http://www.8pic.ir/images/81643667854035628361.jpg
1.088 for cinebench
leeghoofd says:
just want a bulletrpoof retail +6Ghz bencher for 3D 4/4... my quest continues...
der8auer says:
And then you end up with a CB at -90°C and a max clock of 5,8 haha
Farjam says:
nope only only only on this one i was not so bad luck cb is -116 and 3Ds 6350-6400 and 6540 pifast, i buy cpus from one same batch to make sure about not a very bad cb
Dinos22 says:
scatter benching as usual
leeghoofd says:
What did you expect dino
Vivi says:
interesting cache behaviour there albrecht, i have found my chip shut down earlier than normal sessions, so ill try mess with cache a little
nfszocker says:
5.65GHz/1200MHz and 1370m of score, is no good efficiency;)
leeghoofd says:
No tweaks applied to the rams as mentioned in the comment this is done on a daily OS too... just testing a CPU...
Please log in or register to comment.