Submission Details
SF3D`s MaxxMem Ergebnis - Elite League
2617.3 marks mit DDR3 SDRAM at 1130.8MHz
Ranglisten Position
n.a.
Globale Rangliste
n/a
DDR3 SDRAM Rang:
Points earned for overclocker league
-
Globale Punkte (UGP)
Not SF3D's best submission
-
Hardware Punkte (UHP)
Not SF3D's best DDR3 SDRAM submission
Points earned for team league
-
Globale Team Power Punkte (GTPP) Not Team Finland's best submission
0.0 Punkte
-
Hardware Team Power Punkte (HTPP) Not Team Finland's best DDR3 SDRAM submission
0.0 Punkte
Hardware Details
CPU Details
- Model: Intel Core i7 2600K 'Sandy Bridge'
- Kühlung: Water (Custom)
- Cores: 5.512Mhz(+62.12%)
-
Arbeitsspeicher Details
- Produkt: HyperX (classic)
- Kühlung: Air (Stock)
- Typ: 4096MB DDR3 SDRAM
- Geschwindigkeit: @ 1.131Mhz
VGA Details
- Model: ASUS GeForce GTX 580 (GF110) NVIDIA
- Kühlung: Air (Stock)
- Geschwindigkeit: 772Mhz (-.64%) / 1.000Mhz (-.20%)
-
Mainboard Details
- Hersteller: ASUS
- Model: Maximus IV Extreme
- Kühlung: Air (Stock)
- Chipsatz: P67
-
Neueste Kommentare
SF3D Kommentierte sein eigenes Ergebnis:
Kingston KHX2133C8D3T 1K2/4GX Aircooled Scythe Kaze 3000rpm 1.9V still BCLK + divider limited. ASUS did great job with this board!
Asmola sagt:
Insane result! Good work Petri.
What would intel's engineers say about that voltage?
Turrican sagt:
congrats petri, that's a sick result.
TaPaKaH sagt:
Are you sure it's not mem limited? (with 7-7-6 most hypers stop scaling around 1080-1100 and at 1120 they're already barely benchable, no matter the volts)
zoro sagt:
great job! what about the other voltages pll,vccio,vccsa etc...thanks
zoro sagt:
great job! what about the other voltages pll,vccio,vccsa etc...thanks
SF3D sagt:
Sam- It is the cpu clocks which is limiting. I was already doing some higher freq runs, but with lower CPU speed. The score was worse + other issues. So I think with some new CPU I will try to show 1140Mhz+ runs for you
Zoro- 1.9 VDDR, 1.25 VCCSA, 1.1 VCCIO, 1.8VCPUPLL, Skew + driving voltage changes. Subtimings tweaked a tiny bit.
zoro sagt:
It could be bios limited! are you sure about vccsa and vccio? i would expect them to be reverced! is the cpu alive?
SF3D sagt:
Zoro- Yes, I am pretty sure that my eyes does not lie and my fingers set the correct values CPU is still in perfectly good condition.
_mat_ sagt:
Very nice result ... again! 30 GB/s finally done!
That is already a good cpu, I can tell you. Tested 5 until now and only one chip could do 108 BClock, but only with low cpu frequency. Higher frequencies on cpu and ram should need more VCCIO ... as much as the chip can take. Same as it was with Lynnfield.
Your voltages are really strange. Couldn't touch VCCSA on the UD7, because the whole system got unstable. VCCIO is very low for your memory frequency and timings.
SF3D sagt:
Thanks _mat_!
I think MIVE is very good board and very easy to use. I don't know why UD7 behaves that way
Gautam sagt:
1.9v vddr 2250+ 7-7-6 is awesome!
SF3D sagt:
You must mean "only" 1.9V
Dinos22 sagt:
wow i missed this one
well done dude this is a crazy OC. love it
where's ya superpi 32M mate
Bitte einloggen oder register to comment.