Submission Details
Le score de SF3D sur MaxxMem - Elite League
2617.3 marks avec DDR3 SDRAM à 1130.8MHz
Position dans le classement
n/a
Classement général:
n/a
DDR3 SDRAM classement:
Points earned for overclocker league
-
Points Global (UGP)
Not SF3D's best submission
-
Points Hardware (UHP)
Not SF3D's best DDR3 SDRAM submission
Points earned for team league
-
Points Global Team Power (GTPP) Not Team Finland's best submission
0.0 Points
-
Points Hardware Team Power (HTPP) Not Team Finland's best DDR3 SDRAM submission
0.0 Points
Détails matériel
Détails Processeur
- Modèle: Intel Core i7 2600K 'Sandy Bridge'
- Refroidissement: Water (Custom)
- Cores: 5 512MHz(+62.12%)
-
Détails mémoire
- Produit: HyperX (classic)
- Refroidissement: Air (Stock)
- Type: 4096MB DDR3 SDRAM
- Fréquence: @ 1 131MHz
Détails carte graphique
- Modèle: ASUS GeForce GTX 580 (GF110) NVIDIA
- Refroidissement: Air (Stock)
- Fréquence: 772MHz (-.64%) / 1 000MHz (-.20%)
-
Détails carte mère
- Fabricant: ASUS
- Modèle: Maximus IV Extreme
- Refroidissement: Air (Stock)
- Chipset: P67
-
Commentaires récents
SF3D a commenté son propre score:
Kingston KHX2133C8D3T 1K2/4GX Aircooled Scythe Kaze 3000rpm 1.9V still BCLK + divider limited. ASUS did great job with this board!
Asmola dit :
Insane result! Good work Petri.
What would intel's engineers say about that voltage?
Turrican dit :
congrats petri, that's a sick result.
TaPaKaH dit :
Are you sure it's not mem limited? (with 7-7-6 most hypers stop scaling around 1080-1100 and at 1120 they're already barely benchable, no matter the volts)
zoro dit :
great job! what about the other voltages pll,vccio,vccsa etc...thanks
zoro dit :
great job! what about the other voltages pll,vccio,vccsa etc...thanks
SF3D dit :
Sam- It is the cpu clocks which is limiting. I was already doing some higher freq runs, but with lower CPU speed. The score was worse + other issues. So I think with some new CPU I will try to show 1140Mhz+ runs for you
Zoro- 1.9 VDDR, 1.25 VCCSA, 1.1 VCCIO, 1.8VCPUPLL, Skew + driving voltage changes. Subtimings tweaked a tiny bit.
zoro dit :
It could be bios limited! are you sure about vccsa and vccio? i would expect them to be reverced! is the cpu alive?
SF3D dit :
Zoro- Yes, I am pretty sure that my eyes does not lie and my fingers set the correct values CPU is still in perfectly good condition.
_mat_ dit :
Very nice result ... again! 30 GB/s finally done!
That is already a good cpu, I can tell you. Tested 5 until now and only one chip could do 108 BClock, but only with low cpu frequency. Higher frequencies on cpu and ram should need more VCCIO ... as much as the chip can take. Same as it was with Lynnfield.
Your voltages are really strange. Couldn't touch VCCSA on the UD7, because the whole system got unstable. VCCIO is very low for your memory frequency and timings.
SF3D dit :
Thanks _mat_!
I think MIVE is very good board and very easy to use. I don't know why UD7 behaves that way
Gautam dit :
1.9v vddr 2250+ 7-7-6 is awesome!
SF3D dit :
You must mean "only" 1.9V
Dinos22 dit :
wow i missed this one
well done dude this is a crazy OC. love it
where's ya superpi 32M mate
Veuillez vous identifier ou enregister pour commenter